How to run ethernet cable through walls?

Running Ethernet cable through walls is a practical solution for achieving a clean and professional network setup. Whether you want to connect multiple devices or improve internet speeds, having wired connections can offer numerous benefits. While the task may seem daunting, it is actually quite achievable with the right tools and techniques. In this article, we will guide you on how to run Ethernet cable through walls effectively.

How to run Ethernet cable through walls?

To run Ethernet cable through walls, follow these steps:

  1. Plan the route: Determine the starting and ending points for the cable, considering any obstacles or desired concealment.
  2. Gather the necessary tools: You will need a stud finder, fish tape or wire coat hanger, electric drill, cable clips, and a cable tester.
  3. Locate the studs: Use a stud finder to identify the studs in the wall. This will help you avoid drilling into them.
  4. Make the access holes: Drill small holes where you want the cable to enter and exit the wall, ensuring they are large enough for the cable connector to fit through.
  5. Prepare the cable: Strip the outer jacket of the Ethernet cable and expose the inner wires.
  6. Attach the cable to a fish tape or wire coat hanger and feed it through the first access hole.
  7. Guide the cable through the wall: Use the fish tape or wire coat hanger to navigate the cable through the wall, following the planned route. Be patient and gentle to avoid any damage.
  8. Retrieve the cable: Once the cable reaches the exit hole, pull it out from the wall.
  9. Secure the cable: Attach the cable to the wall using cable clips or adhesive-backed cable holders.
  10. Test the connection: Using a cable tester, verify that the Ethernet cable is properly connected and transmitting data.


1. Can I run Ethernet cable through walls on my own?

Yes, with the right tools and guidance, running Ethernet cable through walls can be a DIY project.

2. Which Ethernet cable is best for running through walls?

Cat 6 or Cat 6a cables are recommended as they provide higher bandwidth and better overall performance for long cable runs.

3. Can I run Ethernet cable through walls that have insulation?

Yes, you can run Ethernet cable through insulated walls. You may need to use a fish tape or wire coat hanger to navigate through the insulation.

4. Are there any safety precautions to consider?

When drilling holes, be cautious of electrical wiring, water pipes, or other obstacles that may be hidden within the walls. Use a cable tracer device to avoid any potentially dangerous situations.

5. How long can an Ethernet cable be?

Standard Ethernet cables can be up to 100 meters (328 feet) long. However, consider signal degradation over distance, so it is best to keep cable runs as short as possible.

6. Can I run Ethernet cable through multiple walls?

Yes, you can run Ethernet cable through multiple walls by using the same techniques mentioned earlier. Plan the route carefully and make sure to properly secure the cable along the way.

7. How can I hide the cable after running it through the walls?

You can conceal the cable by covering it with paintable cable raceways, running it behind baseboards or crown moldings, or fishing it through the wall cavity.

8. Can I use existing coaxial cables to run Ethernet signals?

Yes, you can convert coaxial cables into Ethernet cables using MoCA adapters, which allow you to utilize the existing coaxial infrastructure for networking purposes.

9. Is it possible to run Ethernet cable from one floor to another?

Running Ethernet cable vertically between floors can be challenging. In these cases, it may be easier to use powerline adapters or consider investing in a mesh Wi-Fi system.

10. Can I run Ethernet cable through walls without drilling?

If drilling holes is not an option, you can try running the cable through existing conduits, cable ducts, or air vents, if available.

11. Can I use a wireless range extender instead of running Ethernet cables?

While wireless range extenders can enhance Wi-Fi coverage, Ethernet cables provide a more stable and faster connection. For the best performance, it is generally recommended to use wired connections whenever possible.

12. Do I need to ground Ethernet cables?

Ethernet cables do not require grounding unless explicitly specified by local electrical codes or regulations. However, if you are uncertain, consult a licensed electrician to ensure everything is in compliance with safety standards.

Running Ethernet cable through walls may seem overwhelming at first, but with proper planning and execution, it is an achievable task for anyone. By following the steps provided and considering the safety precautions, you can enjoy the benefits of a reliable wired network connection throughout your home or office.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top